Top 10 Rdq Micro M8n Glonass GPS Module – GPS Antennas

As an Amazon Associate I earn from qualifying purchases.

1. Geekstory

#ad

BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory

#ad
Geekstory #ad - This bn-180 gps module can show your speed. 72 searching channel support rate : 4800bps to 921600bps, Default 9600bps. When you use it for Raspberry Pi, there is no driver needed.

Here is connection with RPi, black to gnd, green to txd, red to 3.3v, white to rxd. To make it be rs232 output, you need to use one TTL to RS232 converter cable. The pps led flash means gps module locate your place. The tx led flash means gps module output normally. Data level : ttl or rs-232, default ttl level. This bn-180 gps module does not have flash and cannot be saved. What you will get: 1 x BN-180 GPS Module.
BrandGeekstory #ad
ManufacturerGeekstory #ad
Part Number5823923123
ModelFZ2917

2. Geekstory

#ad

BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control Geekstory

#ad
Geekstory #ad - If you need gps with flash and compass, please buy bn-880 from Geekstory. Bn-220 has flash to save configuration, so you do not need to reset data next time when you use it. But it has no compass. Data level : ttl or rs-232, default ttl level. When you use it for raspberry Pi, there is no driver needed but you need to install software. The tx led flash means gps module output normally. The pps led flash means gps module locate your place. To make it be rs232 output, you need to use one TTL to RS232 converter cable.
BrandGeekstory #ad
ManufacturerGeekstory #ad
Weight0.01 Pounds

3. NEXTION

#ad

BN-220 GPS Module TTL Dual GPS Glonass Navigation with Flash + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Aircraft Flight Control RC FPV Drone

#ad
NEXTION #ad - When you use it for raspberry Pi, there is no driver installation needed but you need to install software. If you have any problem, please contact seller as follow: click "DIYmalls"you can find "Sold by DIYmalls" under Buy Now button, in the new page, click "Ask a question".

Bn220 gps module has flash to save configuration, so you do not need to reset data when you use it next time. Tx led flash means gps module output normally, and PPS LED flash means gps module locate your place. To make it be rs232 output, you need to use one TTL to RS232 converter cable. If you need gps with flash and compass, please buy bn-880 gps. But it has no compass. Data level : ttl or rs-232, default ttl level.
BrandNEXTION #ad
ManufacturerDIYmalls #ad
Modelbn-220

4. DIYmalls

#ad

DIYmalls BN-220 GPS Module TTL Dual GPS Glonass w/Flash + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk CC3D Betaflight Flight Control

#ad
DIYmalls #ad - When you power up bn 220 gps module the first time in a new location, later when you restart bn220 GPS module, it always takes longer to find satillites. If you have any problem, in the new page, please contact seller as follow: click "DIYmalls"you can find "Sold by DIYmalls" under Buy Now button, click "Ask a question".

To make it be rs232 output, you need to use one TTL to RS232 converter cable. Bn220 gps has flash to save configuration, please buy bn-880 gps here, so you do not need to reset data next time when you use it. This is referred to as “cold start”.

Once you’ve done it the first time, it will get a lock much faster. If you need gps with flash and compass, https://www. Amazon. Com/nextion. But bn220 gps doesn't have compass. Data level : ttl or rs-232, default ttl level. When you use it for raspberry Pi, there is no driver installation needed but you need to install software.
BrandDIYmalls #ad
ManufacturerDIYmalls #ad
Weight0.02 Pounds

5. MakerFocus

#ad

GPS Module GPS NEO-6MAr duino GPS, Drone Microcontroller GPS Receiver Compatible with 51 Microcontroller STM32 Ar duino UNO R3 with IPEX Antenna High Sensitivity for Navigation Satellite Positioning

#ad
MakerFocus #ad - Gt-u7 module, its extremely high tracking sensitivity greatly expanded its positioning of the coverage. Note: this gps module will not search for signals when the weather is bad, and it will not search for stars indoors.

With a usb interface, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned. Gpsbaud needs to be set to 9600 instead of 4800; pps pin is not needed unless using the gps to drive a hardware high precision clock; GT-U7 main module GPS module using the original UBLOX 7th generation chip, miniaturization, with high sensitivity, low power consumption, Software is compatible with NEO-6M.

When using it, please make sure that the GPS module is in an open location. Usb directly connected to the computer, with the host computer-owned serial port function, That is, no need for external serial module, send IPX interface active antenna!.
BrandMakerFocus #ad
ManufacturerMakerFocus #ad
Height0.39 Inches
Length1.09 Inches
Weight0.02 Pounds
Width3.94 Inches
Part NumberSN12SF83QOH11452IC

6. Geekstory

#ad

Geekstory GT-U7 GPS Module GPS Receiver Navigation Satellite with EEPROM Compatible with 6M 51 Microcontroller STM32 UO R3+ IPEX Active GPS Antenna for Arduino Drone Raspberry Pi Flight

#ad
Geekstory #ad - Gt-u7 module, with high sensitivity, miniaturization, low power consumption, its extremely high tracking sensitivity greatly expanded its positioning of the coverage. With a usb interface, you can directly connect it with computer.

Usb directly connected to the computer, with the host computer-owned serial port function, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna. That is, no need for external serial module. This gps module is great for vehicle-mounted, camcorders and other mobile positioning systems sharing bike, vehicle monitoring, handheld devices such as PDAs, mobile phones, sharing mobile power etc.

In the ordinary gps receiver module can not locate the place, such as narrow urban sky, dense jungle environment, GT-U7 can be high-precision positioning. Operating voltage: 3. 6v-5v or direct usb power supply; Operating baud rate: 9600 can be modified.
BrandGeekstory #ad
ManufacturerGeekstory #ad
Weight0.01 Pounds

7. Vohappy

#ad

BN-220 GNSS GLONASS Dual GPS Module Antenna Built-in LED Flash TTL Level 9600bps 4M

#ad
Vohappy #ad - When you use it for raspberry Pi, there is no driver needed but you need to install software. The data output when the tx led flashing in blue; PPS LED not bright when GPS not fixed, flashing in red when fixed. Great accuracy: 2. 0 m cep 2d rms sbas enable typical open sky at position Horizontal, 01m/sec 95% sa off at velocity, 1us synchronized to GPS time at Timing. To make it be rs232 output, you need to use one TTL to RS232 converter cable. Bn-220 has flash to save configuration, so you do not need to reset data next time when you use it. Data level: ttl or rs-232, default ttl level.
BrandVohappy #ad
ManufacturerVohappy-12 #ad

8. Geekstory

#ad

BN-880 GPS Module U8 with Flash HMC5883 Compass + GPS Active Antenna Support GPS Glonass Beidou Car Navigation for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller Geekstory

#ad
Geekstory #ad - It is dual module compass, with and electronic compass IC HMC5883L. Dits data level is ttl or rs-232, default ttl level. Bn-880 is suitable for open source flight controller, not for flight control with SCM. To make it be rs232 output, you need to use one TTL to RS232 converter cable. This gps module has flash to save configuration. So you do not need to reset next time when you use it. When you use it for raspberry Pi, there is no driver needed but you need to install software.
BrandGeekstory #ad
ManufacturerGeekstory #ad
Weight0.04 Pounds
Part NumberBeitian BN
ModelFZ2920

9. D-FLIFE

#ad

D-FLIFE BN-880 GPS Module U8 with Flash HMC5883 Compass + GPS Active Antenna Support GPS Glonass Beidou Car Navigation for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller

#ad
D-FLIFE #ad - To make it be rs232 output, you need to use one TTL to RS232 converter cable. It is dual module compass, with and electronic compass IC HMC5883L. When you use it for raspberry Pi, there is no driver needed but you should install software. This gps module has flash to save configuration. Beitian bn-880 is suitable for Open source flight controller, not for flight control with SCM. So you do not need to reset next time when you use it. Dits data level is ttl or rs-232, default ttl level.
BrandD-FLIFE #ad
ManufacturerD-FLIFE #ad

10. DIYmall

#ad

DIYmall 6M GPS Module with EEPROM for MWC/AeroQuad with Antenna for Arduino Flight Control Aircraft

#ad
DIYmall #ad - When you test the gps module, pls kindly note that you need test it in outdoor wide plain place, not indoor. Led signal indicator, With data backup battery. Eeprom power down to save the configuration parameters data.
BrandDIYmall #ad
ManufacturerDIYmall #ad
Height1.18 Inches
Length1.57 Inches
Width0.39 Inches
Part NumberFZ0040
ModelFZ0040